M&P USA Â |Â Made in the USA Â |Â Veteran owned
Z95 MagneRide bypass kit
Plug-and-play shock and ride height simulators for 2015-2020 Cadillac Escalade, Chevrolet Tahoe and Suburban, GMC Yukon Denali, and 2015-2018 Sierra 1500 Denali with Z95 MagneRide. 2009-2014 Escalade owners: check your glove box code.
The M&P USA Z95 MagneRide bypass kit (also called a MagneRide delete kit) lets you replace the factory GM MagneRide (Magnetic Ride Control) shocks with standard passive shocks or coilovers without the “Service Suspension System” warning, fault codes, or the reduced top speed that can come with them. Each kit includes 2 shock simulators and 2 ride height sensor simulators that plug into the factory connectors on one axle, with no cutting or splicing. It fits Z95-equipped Cadillac Escalade, Chevrolet Tahoe and Suburban, GMC Yukon Denali, and GMC Sierra Denali models, including those with rear air suspension. Designed by a US Marine Corps veteran electrical engineer, made in the USA, and backed by our lifetime warranty.
The short answer
- Right kit if your glove box label shows Z95 on a 2015-2020 Escalade, Tahoe, Suburban, or Yukon Denali, a 2015-2018 Sierra 1500 Denali, or a 2009-2014 Escalade. Cadillac used both Z95 and Z55 on the 2009-2014 Escalade, so check the label first (see below).
- One kit covers one axle. For front and rear, the Z95 2-axle kit covers all four corners for less than two single kits.
- No cutting, splicing, or programming. Plug in at each corner, clear the codes, and the warning and speed limit go away.
- 2021-2023 SUV? Its label also says Z95, but it takes the 2021-2023 kit. Need more detail? Read our Z95 MagneRide bypass guide.
On this page
Is this the right Z95 MagneRide bypass kit?
Use this kit if you have a GM truck or SUV with the Z95 MagneRide suspension package (see the fitment table below) and you are removing or replacing the factory MagneRide shocks.
Use a different kit if
- Your vehicle is a car (Camaro, Corvette, ATS, CTS, XTS, SS): use our 2013-2018 strut bypass kit. Cars at stock ride height don’t need ride height simulators. If your car is lowered or raised outside the factory range, some models need them, so contact us first.
- Your SUV is a 2005-2014 model with Z55 AutoRide: use our Z55 bypass kit.
- Your SUV is a 2021-2023 model: use our 2021-2023 kit.
Not sure which package you have? Check the Service Parts Identification label in your glove box for the code Z95, use our Find My Kit tool, or send us your year, make, and model and we’ll confirm the right kit before you order.
2009-2014 Escalade? Check your code
Cadillac used both Z95 MagneRide and Z55 AutoRide on the 2009-2014 Escalade, so on those models the year alone won’t tell you which kit you need.
- 1Open the glove box and find the Service Parts Identification label, a sticker covered in short 3-character codes.
- 2Look for Z95 (use this Z95 MagneRide bypass kit) or Z55 (use our Z55 kit).
- 3Can’t find the label or the code? Send us your VIN and we’ll confirm the right kit before you order.
Before you buy parts, enter your VIN in the NHTSA recall lookup to check for open safety recalls; recall repairs are free at a dealer.
One kit per axle
Each Z95 MagneRide bypass kit covers one axle (front OR rear). Converting both the front and rear? Our Z95 2-axle kit covers all four corners in one order and costs less than two single kits.
What’s included
- 2 MagneRide shock simulators (also called delete modules): replace the electronic signal from the factory shocks so the suspension module sees a normal system.
- 2 ride height simulators: keep the ride height sensor circuit reading normally. GM MagneRide SUVs require these to prevent suspension fault codes.
- Zip ties for mounting, plus printed installation instructions.
Specifications
| Item | Detail |
|---|---|
| Product | Z95 MagneRide bypass kit (MPUSA107) |
| GM option code | Z95 (MagneRide / Magnetic Ride Control) |
| Coverage | One axle (front or rear) per kit |
| Pieces | 4: 2 shock simulators, 2 ride height sensor simulators |
| Shock connector | 2-pin factory plug |
| Ride height connector | 3-pin factory plug |
| Installation | Plug and play, no cutting or splicing |
| After installation | Ride Height Trim Procedure with a scan tool (required on GMC Denali) |
| Warranty | Lifetime |
| Returns | 30 days |
| Made in | USA |
Z95 MagneRide fitment
Plug and play for the following vehicles equipped with the Z95 MagneRide package. Where it says check label, GM used more than one system in those years, so confirm Z95 on your glove box label first.
| Years | Make | Model | Glove box label |
|---|---|---|---|
| 2008 | Cadillac | Escalade, Escalade ESV (Platinum) | Z95 |
| 2009-2014 | Cadillac | Escalade, Escalade ESV, Escalade EXT (EXT through 2013) | Check label (Z95 or Z55) |
| 2009-2013 | GMC | Yukon Denali Hybrid | Z95 |
| 2015-2020 | Cadillac | Escalade, Escalade ESV | Z95 |
| 2015-2020 | Chevrolet | Suburban LTZ (2015-2016), Premier (2017-2020), RST 6.2L Performance Package | Z95 |
| 2015-2020 | Chevrolet | Tahoe LTZ (2015-2016), Premier (2017-2020), RST 6.2L Performance Package | Z95 |
| 2015-2020 | GMC | Yukon Denali, Yukon Denali XL | Z95 |
| 2015-2018 | GMC | Sierra 1500 Denali | Z95 |
Label says Z55? Use our Z55 kit instead. Each kit covers one axle, so front and rear take two kits or the Z95 2-axle kit. Can’t find the label? Send us your VIN.
Customer-reported fitment: customers have used this kit successfully on the 2013 and 2014 Escalade, the 2020 Chevrolet Tahoe RST, and the 2020 GMC Yukon XL Denali, all now in the table above. Vehicle not listed? Contact us to confirm before ordering.
If your shock connector looks different from the one in our photos, send us your year, make, and model before ordering and we’ll help you check.
How to install the Z95 MagneRide bypass kit
- 1Install the ride height simulators first. With the vehicle off and safely raised, release the locking tab on each factory ride height sensor connector, unplug it, and plug in a 3-pin ride height simulator until it clicks.
- 2Cycle the power. Turn the vehicle on for 30 seconds, then off, so the suspension module reads the new ride height.
- 3Install the shock simulators. Unplug the 2-pin connector from each factory MagneRide shock and plug in a 2-pin shock simulator until it clicks.
- 4Secure everything. Zip-tie the ride height simulators through their mounting hole and the shock simulators around their neck. Keep all parts away from the exhaust and other heat sources, and do not secure them against plastic wire loom or wiring. A metal surface is best.
- 5Lower the vehicle, clear codes, and trim. With all four wheels on the ground, start the vehicle. Suspension codes clear within up to 40 ignition cycles, with a scan tool, or by disconnecting the battery for at least 30 minutes. Then perform a Ride Height Trim Procedure with a scan tool: required on GMC Denali models and recommended on all other vehicles. Any mechanic or dealership can do it in a few minutes.
We recommend installation by a certified technician. Full printed instructions are included with every Z95 MagneRide bypass kit. Questions during installation? Contact us.
Why M&P USA
- Built to last: every Z95 MagneRide bypass kit uses sealed, weatherproof OEM-style connections, not crimp connections that corrode over time.
- Lifetime warranty: if a part ever fails, we replace it at no charge.
- Made and supported in the USA by a certified veteran-owned business. Questions before or after your order go to a real person through live chat or our contact form.
- 30-day returns: see our Return & Refund Policy.
Frequently asked questions
Which vehicles does the Z95 MagneRide bypass kit fit?
2015-2020 Cadillac Escalade and Escalade ESV, Chevrolet (Chevy) Suburban and Tahoe, GMC Yukon Denali, and 2015-2018 GMC Sierra 1500 Denali equipped with the Z95 MagneRide package, plus 2009-2014 Escalades and 2009-2013 Yukon Denali Hybrids whose label shows Z95. Look for the code Z95 on the Service Parts Identification label in your glove box.
Is my 2009-2014 Escalade Z95 or Z55?
It could be either. Cadillac used both systems in those years. Check the Service Parts Identification label in your glove box for Z95 or Z55, or send us your VIN and we’ll tell you which kit fits.
Why does my dashboard say “Service Suspension System”?
The suspension module monitors every MagneRide shock and ride height sensor. When a MagneRide shock fails or is replaced with a standard shock, the module loses the signal it expects and sets the warning. The simulators in the Z95 MagneRide bypass kit give the module the signals it expects, so the warning clears once the codes are cleared.
Will it remove the 80 mph speed limit?
Yes. When the suspension module detects a MagneRide fault, many GM vehicles limit top speed (customers report 80 to 85 mph). Once the Z95 MagneRide bypass kit is installed and the codes clear, the limit goes away.
Can I use it with a lift, leveling, or lowering kit?
Yes. Customers have installed the Z95 MagneRide bypass kit with leveling kits, lift kits, and lowered setups. The ride height simulators send the module a steady, normal ride height reading, so the height change does not set suspension codes.
Is this the same as a MagneRide delete resistor?
It does the same job. You may see these parts called MagneRide (also spelled Magnaride, Magna Ride, or Mag Ride) delete kits, delete resistors, bypass resistors, delete modules, delete plugs, shock and suspension bypass kits, or shock simulators. Our Z95 MagneRide bypass kit is a complete plug-and-play set with sealed, weatherproof OEM-style connectors, so there is nothing to cut, solder, or crimp.
Do I need one kit or two?
One Z95 MagneRide bypass kit covers one axle. Converting both the front and rear takes two kits, or get our Z95 2-axle kit, which covers all four corners in one order for less.
Does it require cutting wires or programming?
No wire cutting, splicing, or module programming. The Z95 MagneRide bypass kit plugs into the factory connectors on supported vehicles. After installation, a Ride Height Trim Procedure with a scan tool is required on GMC Denali models and recommended on all other vehicles.
Does it work with rear air suspension (air ride)?
Yes. To keep Automatic Level Control working with non-magnetic rear air shocks, leave the rear ride height sensors connected. If you switch to non-air rear shocks, the rear air lines must be connected to each other so the compressor does not run constantly. The printed instructions show how.
Will it work on my car?
No, the Z95 MagneRide bypass kit is for trucks and SUVs. Cars with MagneRide use our 2013-2018 strut bypass kit.
Still not sure this is your kit?
Use Find My Kit, read the Z95 guide, or send us your VIN and a real person will confirm the right kit before you order.
MagneRide® is a registered trademark of BWI Group. Other names are used only to identify compatible vehicles. M&P USA is not affiliated with, endorsed by, or sponsored by BWI Group or General Motors. Factory part prices and repair costs mentioned are estimates.
Thanks, haitham! Happy it’s working without any issues. We appreciate you choosing a USA-made kit.