M&P USA | Made in the USA | Veteran owned
1997-2012 Car Kit for GM cars
Fits 1997-2012 Corvette C5 and C6, Cadillac CTS-V, STS, DTS and XLR, and Buick Lucerne and LaCrosse.
Truck or SUV? These car kits won’t work on it. An Escalade, Tahoe, Suburban, Yukon, Avalanche or Sierra Denali needs shock and ride height simulators: see MagneRide bypass for GM trucks and SUVs, or go straight to the 2005-2014 Kit, 2015-2020 Kit or 2021-2023 Kit.
The M&P USA 1997-2012 Car Kit is a C6 Corvette MagneRide delete that also fits the C5 and other GM cars with Magnetic Selective Ride Control (F55). It lets you replace failed factory struts or shocks with coilovers or standard shocks, without the “Service Suspension System” or “Shocks Inoperative” warning, fault codes, or the 80 mph speed limit. Each kit has 2 shock simulators that plug into the factory connectors on one axle.
Made in the USA by a certified veteran-owned company and backed by our lifetime warranty.
The short answer
- Fits 1997-2012 GM cars with MagneRide: Corvette C5 and C6 (including the 2013 C6), Cadillac CTS-V (2009-2015), STS, DTS and XLR, and Buick Lucerne and LaCrosse. Look for F55 on the glove box label.
- 2013 or newer car, or a 2012 Camaro ZL1? Use the 2013-2018 Car Kit instead.
- One kit covers one axle. Front OR rear only: 1 kit. Both axles: 2 kits.
- Most plugs click straight in. An adapter for side-by-side plugs is included. Some C6 and XLR rears need one small tab snipped, and the LaCrosse CXS and some early Seville STS need our Pigtail Set.
On this page
C6 Corvette MagneRide delete fitment
The 1997-2012 Car Kit fits these GM cars with MagneRide (Magnetic Selective Ride Control, F55). Not every trim has it, so check the glove box label.
| Years | Make | Model | Note |
|---|---|---|---|
| 1997-2004 | Chevrolet | Corvette C5 | Plug and play |
| 2005-2013 | Chevrolet | Corvette C6 | Some rears: snip the center tab |
| 2004-2009 | Cadillac | XLR, XLR-V | Some rears: snip the center tab |
| 2009-2015 | Cadillac | CTS-V (not the regular CTS) | Plug and play |
| 2006-2011 | Cadillac | DTS with MagneRide | Plug and play |
| 2002-2004 | Cadillac | Seville STS | Some early cars need the Pigtail Set |
| 2005-2011 | Cadillac | STS with MagneRide | Plug and play |
| 2006-2008 | Buick | Lucerne CXS | Plug and play |
| 2008-2011 | Buick | Lucerne Super | Plug and play |
| 2010-2012 | Buick | LaCrosse CXS | Needs the Pigtail Set, one per axle |
2004-2009 Cadillac SRX, an older CVRSS car, or a 2000-2004 Tahoe, Suburban, Yukon or Escalade with AutoRide, or a 2000-2006 Suburban 2500, Yukon XL 2500 or Avalanche 2500? Contact us first. The 2013 Corvette C6 and 2013-2015 CTS-V use this kit; other 2013 and newer cars use the 2013-2018 Car Kit.
Check your plugs before you order
- Most factory shock plugs click straight into our simulators.
- Side-by-side latches? Snap on the adapter included in every kit.
- C6 Corvette and XLR rear: the front plugs in as is. On some rears, snip off the small plastic tab in the center of the simulator’s plug and it clicks in.
- LaCrosse CXS and some early Seville STS: these use a different plug. Splice on our Pigtail Set, one set per axle.
What’s included

- 2 shock simulators for one axle (front OR rear).
- An adapter for side-by-side plugs.
- Zip ties and printed installation instructions.
Specifications
| Item | Detail |
|---|---|
| Product | 1997-2012 Car Kit (MPUSA104) |
| GM system | Magnetic Selective Ride Control (F55), MagneRide on cars |
| Coverage | One axle (front or rear) per kit |
| Pieces | 2 shock simulators, plus an adapter for side-by-side plugs |
| Shock connector | 2-pin GM factory plug (pre-2013 style) |
| Installation | Plug and play on most cars; some C6 and XLR rears need one tab snipped; LaCrosse CXS and some early STS need the Pigtail Set |
| Ride height simulators | Not needed at stock ride height |
| Connectors | Sealed and weatherproof with an O-ring seal |
| Warranty | Lifetime |
| Returns | 30 days |
| Made in | USA |
How to install the 1997-2012 Car Kit
- 1Check your plugs. With the car off and safely raised, compare each factory shock plug with our Check your plugs photo.
- 2Plug in the simulators. Unplug each factory shock or strut and plug a shock simulator into the vehicle-side connector until it clicks. Side-by-side latches: snap on the included adapter. C6 or XLR rear won’t seat? Snip the small center tab first.
- 3Mount to metal. Zip-tie each simulator to a metal surface near its connector, away from the exhaust. Don’t zip-tie it to plastic wire loom or wiring.
- 4Clear the codes. With the wheels on the ground, codes clear within 40 ignition cycles, with a scan tool, or after a 30-minute battery disconnect.
Lowered or raised outside the factory ride height? Some models also need ride height simulators, so contact us first. We recommend installation by a certified technician, and printed instructions come in every kit.
Before you buy parts, enter your VIN in the NHTSA recall lookup to check for open safety recalls; recall repairs are free at a dealer.
Why M&P USA
- Built to last: sealed, weatherproof connectors with an O-ring seal, not crimped wires that corrode over time.
- Lifetime warranty: if a part ever fails, we replace it at no charge.
- Made and supported in the USA by a certified veteran-owned company. Questions before or after your order go to a real person through live chat or our contact form.
- 30-day returns: see our Return & Refund Policy.
Frequently asked questions
Which cars does the 1997-2012 Car Kit fit?
1997-2004 Corvette C5, 2005-2013 Corvette C6, 2009-2015 Cadillac CTS-V (not the regular CTS), 2002-2004 Seville STS and 2005-2011 STS with MagneRide, 2006-2011 DTS with MagneRide, 2004-2009 XLR and XLR-V, 2006-2008 Buick Lucerne CXS, 2008-2011 Lucerne Super, and 2010-2012 Buick LaCrosse CXS (with the Pigtail Set).
Does it fit the 2013 Corvette?
Yes. The 2013 Corvette C6 and the 2013-2015 CTS-V use this kit. Other 2013 and newer cars, and the 2012 Camaro ZL1, use our 2013-2018 Car Kit.
Do I need to modify the rear plug on my C6 Corvette or XLR?
On some of them, yes: snip off the small plastic tab in the center of the simulator’s plug, and the rear plug clicks in. The front plugs in as is.
Will it remove the 80 mph speed limit?
Yes. When the suspension module sees a shock fault, these cars show “Service Suspension System” or “Shocks Inoperative” and limit top speed to about 80 mph. Once the simulators are in and the codes clear, the limit goes away.
Can I use this kit on my truck or SUV?
No. Trucks and SUVs also monitor 3-pin ride height sensors and need ride height simulators. Use the 2005-2014 Kit, 2015-2020 Kit or 2021-2023 Kit instead.
Can I run coilovers or standard shocks?
Yes. That is what the kit is for. Customers run coilovers and standard shocks such as Bilstein on Corvettes, Cadillacs and Buicks.
Do I need one kit or two?
One kit covers one axle. Front OR rear only: 1 kit. Both axles: 2 kits.
Do cars need ride height simulators?
Not at stock ride height. If your car is lowered or raised outside the factory range, some models need them, so contact us first.
Not sure this is your kit?
Use Find My Kit, or send us your year, make, and model and a real person will confirm the right kit before you order.
MagneRide® is a registered trademark of BWI Group. Other names are used only to identify compatible vehicles. M&P USA is not affiliated with, endorsed by, or sponsored by BWI Group or General Motors.


















Leave feedback about this